- Batteries
-
Capacitors
+-
- Non Polarized +-
- Polarized +-
- SMD Capacitors Case A
- SMD Capacitors Case B
- SMD Capacitors Case C
- SMD Capacitors Case D
- SMD Multilayer Ceramic Capacitors 0402 (1005 Metric)
- SMD Multilayer Ceramic Capacitors 0603 (1608 Metric)
- SMD Multilayer Ceramic Capacitors 0805 (2012 Metric)
- SMD Multilayer Ceramic Capacitors 1206 (3216 Metric)
- SMD Multilayer Ceramic Capacitors 1210 (3225 Metric)
- Tantalum Capacitor
- Trimmer Capacitors
- Car Accessories +-
-
Connectors
+-
- Ethernet Cables And Connectors
- Audio Mono and Stereo Connectors
- Banana Connectors
- Barrier Terminal Block
- BLOCK Connectors PCB Type
- Cannon Connectors
- Coaxial Connectors
- Coaxial Connectors (SMA-SMB-SMC)
- Crimp Terminal Connectors
- Crimp Terminal Connectors Ring Type
- Crocodile Connectors
- D-SUB Connectors
- DC Connectors
- Dupont TJC Connectors
- IDC Connectors 2.0mm Pitch
- IDC Connectors 2.54mm Pitch
- Nylon Insulated Cord End Terminals
- USB Connectors
- Wire to Board Connectors
- Wire to Wire Connectors
- Wire to Wire SM Connectors
- Cooling Fans
- Crystal Oscillators
- Diodes +-
- Electronics Project Boxes
- Fuses and Breaker +-
- Gadgets and Gifts +-
- Heat Shrink Sleeves
- Heat Sink
- IC Base and Headers +-
- ICs +-
- Inductors +-
- Kits +-
- Knobs
- LCDs
- LIGHTS +-
- Magnets
- MicroControllers +-
- Motors +-
- PCBs +-
-
Potentiometers
+-
- Gear Tuning Potentiometer
- SMD Tuning Potentiometer
- 3006P Multiturn Precision Potentiometer
- 3296 Multiturn Precision Potentiometer
- 3362 Trimming Potentiometer
- 3386 Trimming Potentiometer
- WH06-1
- 3590 Wirewound Potentiometer
- WH06-2
- WH112A-2
- Knob Big
- WH148-1A
- WH148-1B
- Semi-Fixed (SR083)
- WTH118-1A Wire Wound
- Slide Potentiometers
- Shaft
- Trimmer Resistors
- WF-905CL
- Power Supply +-
- Relays +-
-
Resistors
+-
- SMD Resistors 0402 1005 Metric .06W 5%
- SMD Resistors 0603 0201 Metric .1W 1%
- SMD Resistors 0603 0201 Metric .1W 5%
- SMD Resistors 0805 2012 Metric .125W 1%
- SMD Resistors 0805 2012 Metric .125W 5%
- SMD Resistors 1206 3216 Metric .25W 5%
- SMD Resistors 2010 5025 Metric .75W 1%
- SMD Resistors 2512 6332 Metric 1W 5%
- 1/8W (+-0.1%) Carbon Film Fixed Resistor
- 1/8W (+- 1%) Carbon Film Fixed Resistor
- 1/8W (+- 5%) Carbon Film Fixed Resistor
- .25w (+-1%) Carbon Film Fixed Resistor
- .25w (+-5%) Carbon Film Fixed Resistor
- 1/2W (+- 5%) Carbon Film Fixed Resistor
- 1W (+- 5%) Carbon Film Fixed Resistor
- 2W (+- 5%) Carbon Film Fixed Resistor
- 5W (+- 5%) Fix Wirewound Cement Resistor
- 10W (+- 5%) Fix Wirewound Cement Resistor
- DIP Resistor Network
- SIP Resistor Network
- Rezonators
- Sensors +-
- Smart Boards +-
- Speakers and Buzzers
- Switches +-
- Thermistors +-
- Tools +-
- Transistors +-
- Varistors
- Voltage Regulators +-
- Wires and Cables +-
Rs. SKU: 7696
Availability: In Stock
DP30V5A-L Programmable 0-32V 5A 160W Digital Constant Power Supply Module
Technical Parameters:
Input voltage range: 6-40.00V
Output voltage range: 0V-32.00V
Output current: 0-5.100A
Output power range: 0-160W
Product Weight: 66g
Product Dimension: 85*58*31(mm) (L*W*H)
Output voltage resolution: 0.01V
Output current resolution: 0.001A
Output Voltage accuracy: ± (0.5% + 1 digits)
Output Current accuracy: ± (1% + 3 digits)
Ripple Wave (full load 40v to 32V/5A): about 100 mV VPP
Note: On the status of output, the Input must be 1 V higher than the output. Please strengthen the heat dissipation when working with big current.
Operating Instructions:
1. Open or close output: press ON/OFF button one time to open or close output in any state; press again, output will be closed or open, followed by recycling. When closed output, the LED display will show “OFF”.2
2. Set output voltage and current: Press SET shortly, the led display will be blinking. You can press the two buttons (+ key and - key) on the tube left to increase or decrease the value. Press SET key shortly again to switch 0.01V to 0.1V to 1V to 0.01A to 0.1A to 1A to exist adjustment, followed by recycling. At the corresponding value place, you can press the two buttons (+ key and - key) to increase or decrease the value. if you don’t press the set key, the set mode will be automatically exited after 6s and the current set value will be automatically stored.
3. Switch input and output display: At no output state, press the two buttons on the tube left (IN key and OUT key) to switch the tube display between the current input voltage and the current output voltage. When show input voltage, “IN” LED lights; when show output voltage, “OUT” LED lights. 4.
4. CC and CV indication: When the module is in the state of constant voltage (CV) or constant current (CC), the CC or CV led will lights correspond to show CV or CC state.
5. Output current zero calibration: In the no-load state, Keep pressing SET key to power on, when the led display flashed, the calibration is done. Then you can loosen the SET key.
6. Store set value automatically: in operation process, the led display state, output current and output voltage setting value and output state are automatically stored. When power on next time, the default work state is the stored state.
Package List:
1 x DP30V5A-L LED Display Converter Module
Buy Electronics parts through EVE-eVision Electronics Pakistan, Pakistan's first online electronics store.