- Batteries
-
Capacitors
+-
- Non Polarized +-
- Polarized +-
- SMD Capacitors Case A
- SMD Capacitors Case B
- SMD Capacitors Case C
- SMD Capacitors Case D
- SMD Multilayer Ceramic Capacitors 0402 (1005 Metric)
- SMD Multilayer Ceramic Capacitors 0603 (1608 Metric)
- SMD Multilayer Ceramic Capacitors 0805 (2012 Metric)
- SMD Multilayer Ceramic Capacitors 1206 (3216 Metric)
- SMD Multilayer Ceramic Capacitors 1210 (3225 Metric)
- Tantalum Capacitor
- Trimmer Capacitors
- Car Accessories +-
-
Connectors
+-
- Ethernet Cables And Connectors
- Audio Mono and Stereo Connectors
- Banana Connectors
- Barrier Terminal Block
- BLOCK Connectors PCB Type
- Cannon Connectors
- Coaxial Connectors
- Coaxial Connectors (SMA-SMB-SMC)
- Crimp Terminal Connectors
- Crimp Terminal Connectors Ring Type
- Crocodile Connectors
- D-SUB Connectors
- DC Connectors
- Dupont TJC Connectors
- IDC Connectors 2.0mm Pitch
- IDC Connectors 2.54mm Pitch
- Nylon Insulated Cord End Terminals
- USB Connectors
- Wire to Board Connectors
- Wire to Wire Connectors
- Wire to Wire SM Connectors
- Cooling Fans
- Crystal Oscillators
- Diodes +-
- Electronics Project Boxes
- Fuses and Breaker +-
- Gadgets and Gifts +-
- Heat Shrink Sleeves
- Heat Sink
- IC Base and Headers +-
- ICs +-
- Inductors +-
- Kits +-
- Knobs
- LCDs
- LIGHTS +-
- Magnets
- MicroControllers +-
- Motors +-
- PCBs +-
-
Potentiometers
+-
- Gear Tuning Potentiometer
- SMD Tuning Potentiometer
- 3006P Multiturn Precision Potentiometer
- 3296 Multiturn Precision Potentiometer
- 3362 Trimming Potentiometer
- 3386 Trimming Potentiometer
- WH06-1
- 3590 Wirewound Potentiometer
- WH06-2
- WH112A-2
- Knob Big
- WH148-1A
- WH148-1B
- Semi-Fixed (SR083)
- WTH118-1A Wire Wound
- Slide Potentiometers
- Shaft
- Trimmer Resistors
- WF-905CL
- Power Supply +-
- Relays +-
-
Resistors
+-
- SMD Resistors 0402 1005 Metric .06W 5%
- SMD Resistors 0603 0201 Metric .1W 1%
- SMD Resistors 0603 0201 Metric .1W 5%
- SMD Resistors 0805 2012 Metric .125W 1%
- SMD Resistors 0805 2012 Metric .125W 5%
- SMD Resistors 1206 3216 Metric .25W 5%
- SMD Resistors 2010 5025 Metric .75W 1%
- SMD Resistors 2512 6332 Metric 1W 5%
- 1/8W (+-0.1%) Carbon Film Fixed Resistor
- 1/8W (+- 1%) Carbon Film Fixed Resistor
- 1/8W (+- 5%) Carbon Film Fixed Resistor
- .25w (+-1%) Carbon Film Fixed Resistor
- .25w (+-5%) Carbon Film Fixed Resistor
- 1/2W (+- 5%) Carbon Film Fixed Resistor
- 1W (+- 5%) Carbon Film Fixed Resistor
- 2W (+- 5%) Carbon Film Fixed Resistor
- 5W (+- 5%) Fix Wirewound Cement Resistor
- 10W (+- 5%) Fix Wirewound Cement Resistor
- DIP Resistor Network
- SIP Resistor Network
- Rezonators
- Sensors +-
- Smart Boards +-
- Speakers and Buzzers
- Switches +-
- Thermistors +-
- Tools +-
- Transistors +-
- Varistors
- Voltage Regulators +-
- Wires and Cables +-
Rs. SKU: 5585
Availability: In Stock
CD74HC4067 16-Channel Analog Digital Multiplexer Breakout Board Module L5
This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
This chip is like a rotary switch - it internally routes the common pin
(COM in the schematic, SIG on the board)to one of 16 channel pins (CHANxx).
It works with both digital and analog signals (the voltage can’t be higher than VCC),
and the connections function in either direction.
To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3),
and send it the binary address of the channel you want (see the datasheet for details).
This allows you to connect up to 16 sensors to your system using only 5 pins!
Since the mux/demux also works with digital signals,
you can use it to pipe TTL-level serial data to or from multiple devices.
For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller.
You can then select any one of those 16 devices to listen to.
If you want two-way communications, you can add a second board to route
your microcontroller’s TX line to 16 device’s RX lines.
By using multiple boards, you can create similar arrangements for I2C, SPI, etc.
The internal switches are bidirectional, support voltages between ground and VCC,
have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching.
The board also breaks out the chip’s “enable” pin, which when driven high,
will completely disconnect the common pin (all switches “off”).
Features:
1. 2V to 6V operation
2. “On” resistance: 70 Ohms @ 4.5V
3. 6ns break-before-make @ 4.5V
4. Wide operating temperature range: -55C to 125C
Buy Electronics parts through EVE-eVision Electronics Pakistan, Pakistan's first online electronics store.